Plazminis pjoviklis - 85 A - 400 V - STAMOS 10020044 S-PLASMA 85H bandomasis lankas

Reliable plasma cutter by Stamos Germany is equipment for cutting and punching metals such as steel and its alloys, stainless steel, cast iron, copper, nickel, aluminum.It is therefore perfect for renovation and maintenance works.The machine is characterized by precision, reliability and mobility, and compared to competing products, it is distinguished by a large range of cutting current values (20 - 85 A) and cutting thickness 27 mm PARAMETERS: Rated input voltage 400 V, 3-FazoweCzęstotliwość mains 50 Hz Rated input current 13,2 A Maximum input current 18,6 A Power Rated input 8,6 kVA Maximum input power 13,2 kVA No-load voltage 850 V Cutting current 851 - 852 A Rated operating cycle 853 cutting in the working cycle 854 855 A Cutting current in the working cycle 856 857 A Gas flow time 858 - 859 s Maximum cut thickness 270 mm Cutting width 271 mm 272 Required air flow l / min Working air pressure 273 bar Plasma torch 274 m Ground cable with clamp 275 m Air nozzle 276 m Power cable 277 m Cooling the case Fan Cooling the handle Air Power factor 278 (in nominal conditions) ≥ 279 of insulation F Design compliant with EN 4000 / EN Protection dimensions 4002 s (LxWxH) 4003 x 4004 x 4005 cm Weight 4006 kg Shipping dimensions (LxWxH) 4007 x 4008 x 4009 cm Shipping weight 3-FazoweCzęstotliwość0 kg Plasma cutting using the offered equipment is a process characterized by high efficiency and precision.The equipment can handle the processing of materials such as steel and its alloys, stainless steel, cast iron, copper, nickel, aluminum, ensuring high cutting speed without the need for preheating.Thanks to the precise pressure control, the cuts are smooth and do not require grinding, and the thin surfaces do not burn.The minimum amount of waste generated during the trimming process guarantees no distortion of the material FEATURES: Efficiency - thanks to IGBT technology Versatility - for various types of metals Ergonomics - availability of useful HF functions, 2T/4T, gas flow after cutting Safety - overheating protection system and efficient fan Mobility - small dimensions and weight as well as comfortable handle Additional functions that improve the quality of work available to the user of the presented equipment are: Non-contact arc ignition (HF) - enables the commencement of plasma cutting without the need for direct contact of the torch with the material to be connected. The arc is initiated in this case by holding down the button on the handle.The end of work occurs when the button is released.This function is useful during short machining. The 4T – mode shortly pressing the button on the handle initiates the plasma arc.The work ends after the second short press of the button.Function useful during long periods of operation. APPLIED TECHNOLOGIES: IGBT - Insulated Gate Bipolar Transistor is a semiconductor element that is increasingly used in power electronics.It combines the advantages of two types of transistors: the ease of control of field-effect transistors and high breakdown voltage, and the switching speed of bipolar transistors.Short-circuit resistance is also an advantage as the IGBT limits the current flow.IGBTs are a newer continuation of the MOSFET technology.This guarantees a long service life and high quality of the device FANS - provide optimal heat dissipation during device operation CONNECTIONS: GAS / AIR CONNECTION - gas with the required pressure is used during plasma arc cutting.Before starting, ground them with a wire, the cross-section of which must not be smaller than 6 mmPRZYŁĄCZE MASS CLAMP CONNECTION OF THE PLASMA ARC CUTTING HOLDER POWER SUPPLY - the device is powered from three phases (3 x 400 V +/- 10 %).FUNKCJE:BEZDOTYKOWE PLASMA ARC IGNITION without the need for contact with the material.The function increases the efficiency and comfort of work and has a positive effect on the wear of consumables CUTTING CURRENT GAS FLOW AFTER WELDING - the time after welding, in which gas flows from the torch, cooling it and protecting the weld from utlenieniem2T - function means starting work after pressing the button on the handle and stopping it after welding. When the uchwycie4T - button is released, pressing the button on the handle opens the solenoid valve, gas is pre-flowed and the electric arc is ignited.After ignition, the current is equal to the starting current.When the button is released, the value of the output current increases to the value of the welding current.The welding process is stopped by pressing the button on the PLASMA ARC CHUCK again - the dense plasma arc melts the metal and throws it out of the slot thanks to the kinetic energy provided by compressed air. 4 m Air nozzle - 4 m Pressure regulator Manometer Components for the plasma torch Operation manual ...