merXu
Cancel

White corundum waterproof anti-slip tape FLOMA Marine - length 18.3 m, width 5 cm and thickness 0.99 mm

Manufacturer
FLOMAT
property
waterproof
material
corundum
model
Marine
length
18.3 m
use
anti-slip protection
Show more
CZK 866.59
€34.19
1 pc.
CZK 866.59+VAT
€34.19
1 ×
CZK 866.59
(1 pc.)
  • Check before buy
  • Full flexibility
  • Free assistance
  • Minimum order volume 1 pc.
  • Country of dispatch Czechia
  • Destination countries Poland, Czechia, Slovakia, Estonia, Lithuania
F
verified supplier
FLOMAT s.r.o.
Contact supplier
See all offers
see report
Parameters
Manufacturer
FLOMAT
property
waterproof
material
corundum
model
Marine
length
18.3 m
use
anti-slip protection
width
5 cm
mark
FLOMA
color
White color
thickness
0.99 mm
Description

Anti-slip tape designed primarily for applications in environments where there is salt water, to which the tape is 100% resistant.The tape can be used, for example, on recreational craft, racing boats, yachts and commercial boats sailing out to sea.Thanks to the easy maintenance of cleanliness, the tape can also be used in environments with a strict standard of hygiene, such as kitchens.

In contrast to the classic corundum tape, the tape is coated with a special anti-slip layer with a S2 grit formed of small glass beads.The ball layer guarantees comfortable walking on the belt and bare feet and is also gentle in textiles.

For a long life of the tape, it is necessary to follow the correct procedure of its application on a dry and clean surface.

The most common use of
  • recreational craft, racing boats, yachts and boats sailing out to sea
  • kitchen
Features
  • anti-slip layer < / li>
  • self-adhesive layer
  • water resistance, salt resistance
Technical description
  • color:
  • liner material: PVC < / li>
  • material: S2
  • glue: acrylic
  • length: 18,3 m
  • width: 50 mm
  • thickness: 0.99 mm
  • adhesion to steel: 1500 ↑ (g / 25.4 mm2; PSTC-4 test)
  • tensile strength: 5 ↑ (kg / 25, 4 mm2; PSTC-31 test)
  • elongation at break: 5% ↑ (PSTC-31 test)
  • water resistance: 10 months (PSTC-35 test)
  • Chemical resistance: 8 months (PSTC-35 test)
  • Engine oil resistance: Excellent (PSTC-35 test)
  • Operating temperature: -30 to +70 ° C
Assembly / installation
  • Prior to use, ensure that the tape is stored in its packaging (if supplied), dry and min. temperature of 10 ° C.
  • Before gluing, it is necessary to remove all dirt and grease from the target surface.Do not use methyl alcohol, benzine, lighter fluid or other liquids that could leave a greasy film.
  • The surface to be applied to the tape should be at least 10 ° C (unless stated otherwise in the technical parameters).
  • Porous surfaces must be sealed before application to prevent the adhesive from being attacked by water.Toluene-based primers are ideal.Apply a thin layer to the cleaned surface with a brush and then allow to dry.
  • To apply the tape, peel off the back of the release liner, then press the adhesive firmly against the prepared surface and slowly continue to peel off the liner.Try to ensure that the tape is not stretched.
  • After applying the tape, press firmly with even pressure (it is ideal to use a roller).
  • To extend the life of the product, we recommend sealing the edges of the tape with an "edge fixer".To fix, apply a small amount along the edges of the tape.
  • If the tape is applied correctly, the new anti-slip surface is immediately walkable, even after 48 hours the adhesive system acquires the best properties.