Plasma cutter - 120 A - 400 V - 45 mm STAMOS 10021245 S-CUTTER 120C

The most important features produktu120 A/400 Cutting depth 45 mmLED displayIgnition HFIGBT Specifications Model S-CUTTER 120CNr catalog 10021245Stan article NewVoltage 400 Length of the power cord 3 mHand coolingGas coolingHousing coolingAir coolingInput power 18,2 kVAMax. input power 19,4 kVARated input current 18,1 Amax. input current 27,8 AInsulation class FProtection level IP21SZapłon HFMaximum input current 22,6 Acutting current per duty cycle 100% 93 Acutting current per duty cycle 60% 120 A work cycle for 40°C 60%Napięcie barren 340 VW power factor 0,93Zgodność with standards EN61558-1/EN61558-2-16Długość ground wire 3 mPlasma cable length 5 mMin. cutting current 30 Amax. cutting current 120 Amax. cutting thickness Carbon steel –45 mm Post-flow gas time 10 Performance 85%Chłodzenie water NoCNC NoManual YesDimensions (LxWxH)65 x 40 x 58 cm weight 37 kgShipping dimensions (LxWxH)75 x 50 x 68 cmShipping weight 42,8 kgScope of deliveryWe offer the following set:Plasma cutterBurner P80Przewód grounding 3 m 16 mm2Wąż gas 8 x 12 (3 m) User manual The whole thing is well protected for transport. Functions IGBT - Insulated Gate Bipolar Transistor is a semiconductor element that is increasingly used in power electronics.It combines the advantages of two types of transistors: the ease of control of field-effect transistors and high breakdown voltage, and the switching speed of bipolar transistors.Short-circuit resistance is also an advantage as the IGBT limits the current flow.IGBTs are a newer continuation of MOSFET technology.FANS - ensure optimal heat dissipation during operation of the device.GAS / AIR CONNECTION - during plasma arc cutting, gas with the required pressure is used. GROUNDING - at the back of each device there is a screw with a grounding marking.Before starting, they must be grounded using a cable whose cross-section must not be less than 6 mm².CONNECTION OF THE TORCH FOR PLASMA ARC CUTTING SUPPLY VOLTAGE - the device is powered from three phases (3 x 400 V +/- 10 %).NON-CONTACT ARC STARTING - allows you to create a clean starting point of the weld in TIG mode (using high frequency).CURRENT RISE TIME  - the time during which the output current value increases: from the initial current value to the welding current value.CURRENT DOWNLOAD - the time during which the output current value decreases: from the welding current value to the final current value.PLASMA ARC CUTTING  - a dense plasma arc melts the metal and throws it out of the gap thanks to the kinetic energy given to it by compressed air.LED DISPLAY - shows welding / cutting parameters.OVERLOAD / FAILURE - the lamp lights up in two situations: a) if the machine has failed and cannot be operated, b) if the device has exceeded the standard duty cycle and the overheating protection mode has been activated.In this mode, leave them with the power on.If the red light goes out, the device has cooled down to operating temperature and can be used again.Key informationGreat performance -120 And at 60% work cycle,93 And at 100% duty cycle Efficiency - modern IGBT inverter technology Proven solution - non-contact high-frequency ignition Power - cutting depth up to 45 mm depending on the metal Maximum control - easy-to-read control panel with LED display Plasma cutter -120 A-400 V-45 The Stamos Power plasma cutter is a professional equipment for cutting and gouging materials using a plasma stream.Model S-CUTTER 120C suitable for processing non-alloy, low-alloy and high-alloy steel, nickel, copper, titanium, zirconium and their alloys.It will work not only in repair and renovation works in the workshop, but also in many industries: aviation, machinery, automotive, shipbuilding, etc. Plasma cutter - description The use of IGBT technology significantly increases the efficiency of the Stamos Power plasma cutter.It uses a three-pin power semiconductor as an electronic switch.This solution makes the S-CUTTER 120C is characterized by high efficiency, efficient change of operating modes and a low failure rate. Reliable arc ignition without contact with the workpiece is due to high-frequency HF ignition.The cutting current is 30-120 Ah, and the work cycle 60%, which also increases efficiency.The machine allows you to quickly cut carbon steel elements of maximum thickness 45 mm. Has a function of end-flow time gazu (10 s).Overload protection and ventilation protect against overheating, thus extending the life of the device. Model S-CUTTER 120C has a small and compact design, which works well in small workshops.The housing made of coated steel sheet protects against mechanical damage.